Section 408.7003. Applicability of national standards.

The following standards are adopted by reference.

(a)    The following standards are available from the American Society of Mechanical Engineers (ASME), 22 Law Drive, Box 2900, Fairfield, New Jersey 07007-2900, at a cost as of the time of adoption of these rules, as stated in this subrule:

(i)     ASME A17.1-2010 safety code for elevators and escalators, except for sections, 2.5.1.5.3, 2.8.3.3.2, 2.8.6, 2.11.1.3, 2.11.1.4, 2.11.7.2, 2.11.7.2.1, 2.11.7.2.2, 2.11.7.2.3, 2.11.7.2.4, 2.11.7.2.5, 2.14.2.2(f), 2.14.2.6, 2.14.5.8.2, 2.16.5.1.3, 2.22.2, 3.18.3.8.3, 3.19.5.2, 3.22.1.6, 5.3.1.1.1, 5.3.1.1.2, 5.3.1.2.1, 5.3.1.14.3, 5.4.10.2, 8.6.5.8, 8.6.11.5 to 8.6.11.5.6, 8.10.1.1.3, 8.11.1.1, 8.11.1.1.1, 8.11.1.1.2.  Cost $310.00.

(ii)     ASME A17.2-2012 guide for inspection of elevators, escalators, and moving walks. Cost $180.00.

(iii)     ASME A17.6-2010 standard for elevator suspension, compensation, and governor systems.  Cost $90.00.

(iv)     ASME A17.7-2007 performance-based safety code for elevators and escalators, except for where the Michigan elevator rules make an exception to, addition to, or an amendment of, an ASME A17.1/CA B44 code section the Michigan elevator rules shall govern over the corresponding section in ASME A17.7/CSA B44.7 and must obtain department approval.  Cost $155.00.

(v)     ASME A18.1-2011 safety code standard for platform lifts and stairway chairlifts, except for sections 2.1.2 to 2.1.2.8, 2.1.3 to 2.1.3.10, 3.10.2  to 3.10.2.4, 10.1.1, 10.1.2 to 10.1.2.3, 10.1.3.3, 10.1.4, and 10.2.1.  Cost $90.00.

(vi)     ASME A90.1-2009 safety standard for belt manlifts.  Cost $59.00.

(b)     ANSI A10.4-2007, the American national standards institute (ANSI), safety requirements for personnel hoist and employee elevators for construction and demolition and operations, except for sections 24.1.2.1 and 26.4.8.1, is available from ANSI at 1430 Broadway, New York, New York, 10018.  Cost $74.00.

(c)     The following standards are available from American Society for Testing and Materials, (ASTM), 100 Bar Harbor Drive, 2 Conshohocken, PA 19428-2959, at a cost as of the time of adoption of these rules, as stated in this subrule:

(i)     ASTM D 2667-2008, ‘Standard test method for biodegradability of alkylbenzene sulfonates’. Cost $47.00.

(ii)     ASTM E 648-2010, standard test method for critical radiant flux of floor- covering systems using a radiant heat energy source. Cost $47.00.

(ii)     ASTM E 648-2010, standard test method for critical radiant flux of floor- covering systems using a radiant heat energy source. Cost $47.00.

(iii)     ASTM F 714-2012, standard specification for polyethylene (PE) plastic pipe (SDR-PR) based on outside diameter’.  Cost $47.00.

(d)    The standards adopted in this subrule are also available for inspection at the Michigan Department of Licensing and Regulatory Affairs, Bureau of Construction Codes, 2501 Woodlake Circle, Okemos, Michigan 48864.  Copies may be obtained from the bureau at the cost of the individual codes as noted in this subrule, plus the department's cost for shipping and handling.

(e)     All references to NFPA 70-2011 mean the Michigan electrical code. The Michigan electrical code is available for inspection or may be purchased from the Michigan Department of Licensing and Regulatory Affairs, Bureau of Construction Codes 2501 Woodlake Circle, Okemos, Michigan 48864, at a cost as of the time of adoption of these amendatory rules of $89.50.

History: 2003 AACS; 2005 AACS; 2010 AACS; 2014 AACS. .